隨著使用硬管內窺鏡的范圍擴大，各科醫生使用硬管內窺鏡頻率越來越高。硬管內窺鏡是比較嬌貴的醫療器械，但是只要能夠正確的使用和維護，就可以避免損壞。
內窺鏡設備維修人員下面來為你講解。
With the expansion of the scope of using rigid tube endoscopes, doctors in various departments use rigid tube endoscopes more and more frequently. Hard tube endoscope is a relatively delicate medical instrument, but as long as it can be used and maintained correctly, it can avoid damage. The maintenance personnel of endoscope equipment will explain it to you below.
1.硬管內窺鏡使用完后應沖洗干凈，把水漬涼干，鏡頭前端有污漬時應用鏡頭紙、棉簽或細紗布輕輕擦拭。
1. The rigid tube endoscope shall be rinsed after use, and the water stain shall be dried. When there is stain on the front end of the lens, the lens paper, cotton swab or fine gauze shall be used to gently wipe.
2.硬管內窺鏡應有專人專柜保管，放在專用的包裝箱內，內襯柔軟的海綿或聚氨酯泡沫。
2. The rigid tube endoscope shall be kept by a special person in a special cabinet and placed in a special packing box lined with soft sponge or polyurethane foam.
3.所有硬管內窺鏡和手術器械都要碼放整齊，不得交叉重疊放置，確保箱蓋蓋好后，內部的窺鏡和器械不會在搬運時相互撞擊。
3. All rigid tube endoscopes and surgical instruments shall be stacked neatly, and shall not be overlapped with each other to ensure that the endoscope and instruments inside will not collide with each other during handling after the case cover is closed.
4.取出或放入硬管內窺鏡時，應雙手平托，輕拿輕放。由于內窺鏡的鏡管很薄，受到擠壓、磕碰、折彎、落地等情況就會彎曲變形，導致鏡片破損或光軸偏移而造成圖像不清楚或不能使用，所以從包裝箱中取出或放入硬管內窺鏡時，應雙手平托輕輕地取出或放入，切忌提起一段拽出。
4. When taking out or putting in the rigid tube endoscope, hold it flat with both hands and handle it gently. Since the endoscope tube is very thin, it will bend and deform under extrusion, collision, bending, landing, etc., resulting in lens damage or optical axis offset, resulting in unclear or unusable images. Therefore, when taking out or putting in the rigid tube endoscope from the packaging box, it should be gently taken out or put in with both hands flat, and it is not allowed to pull out a section.
5.硬管內窺鏡放在托盤等硬質容器內移動時，注意與其他器械分開放置，不要過分顛簸，以免碰撞到窺鏡。
5. When the rigid tube endoscope is placed in a hard container such as a tray and moved, it shall be placed separately from other instruments, and shall not be unduly bumped to avoid collision with the endoscope.
6.包裝箱內應備有干燥劑保持箱內干燥。
6. The packing box shall be equipped with desiccant to keep the box dry.
7.有些硬管內窺鏡不耐高溫高壓，這主要是因為其鏡端封裝用的環氧樹脂膠在高溫高壓下會開膠而造成鏡管內進水，光學系統進水后就會產生視野模糊，所以這類內窺鏡不能用煮沸和高壓蒸汽等高溫高壓的方法。
7. Some rigid tube endoscopes are not resistant to high temperature and high pressure. This is mainly because the epoxy resin glue used for the lens end encapsulation will open under high temperature and high pressure, which will cause water in the lens tube. After the optical system enters the water, the field of vision will be blurred. Therefore, such endoscopes cannot use high temperature and high pressure methods such as boiling and high pressure steam.
Please pay special attention to the maintenance when using the rigid tube endoscope. That's all. If you don't know anything about this, you can come to our website at any time http://www.dibeisi.top Consult.
新聞資訊
聯系我們
公司：匠仁醫療設備有限公司 
新聞資訊
